Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
I'm using Ant sdh,I want to make system enter sleep,how to disable nrf_sdh_ant?
I usd this function to enable sdh,but can't disable sdh to enter sleep,how to use?
static...
Hello,
1.Which platform is recommended for developing Bluetooth mesh, nrf5-sdk-for-mesh or NCS?
2.What is the difference between nrf5-sdk-for-mesh and NCS?
3.What is...
Hello Devzone Community,
I am facing a run time, peripheral or sensor initialization error in a Zephyr based app, built using sdk-nrf v1.6.1, and its corresponding Zephyr...
My Zephyr based application is buildable and working fine. I followed this tutorial, trying to enable bluetooth OTA for my app: Add DFU support to your application - Software...
Programmer 2.0 is broken in nRF Connect for Desktop v3.8.0
Very often it does not detect connected devices, even if I disconnect and reconnect the nRF9160DK which is also...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
I used \ncs\v1.8.0\bootloader\mcuboot\samples\zephyr\hello-world as a starting...
Hello,
We have a battery-powered product that currently uses the NRF52832. It is a very low power space-constrained application, so we always evaluate any potential current...
Hello,
I have set my softdevice s132v3 with SDK12.2 and nrf52832 to use connection event length extension and data length extende with connection parameters as shown below...
Hello,
I'm currently trying to implement a simple scenario: Using the nRF52840_Dongle, provide LOG output to the console.
This is the main program:
This is the usb_console...
Two Factor Authentification is enabled for my primary account (I had to create a second one to ask question).
Something has gone wrong with setting up two factor authentification...
I wanted to implement a time sync feature on nRF-52840 DK. I took a reference from this example, but there were certain things unclear to me.
Can somebody explain to me...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
