Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am developing Coap-Client and Coap-Server devices using nRf52840 dev kit. I am using ncs 1.7.1 sdk. I have a few questions.
1- I can successfully send a data received...
Hello all,
I have recently developed a custom board that uses an nrf52810. It also contains an accelerometer as well as some hardware for regulating the voltage and charging...
hi
I am using nRF5 Calendar example and
I have this problem
could you help me, how can I fix that?
I don't use the UART functions, I'm going to use SSD1306 to...
Hello!
I am currently working with Actinius' Icarus IoT board and I'm trying to get the interrupts to work. This is the boards' pin layout: At the moment I have connected...
Hi everyone,
I am trying to create a system to collect data from different sensors and store them in a FRAM. Then by using SPI, I want to transfer the data to the nRF52832...
Hi,
Trying to build the asset_tracker_v2 application I finally get the following error:
Rebuilding ‘zephyr / zephyr.elf’ from solution ‘build’ in configuration ‘Common...
Hi All,
I have problem running nRF5340 in continuous mode without any external trigger (timer/ppi). I would like to setup SAADC so that last conversion triggered new set...
Hello there, can I use the JTAG interface of the nrf52840 to perform a boundary scan of the components connected to it? I'd like to have fewer testpoints in my pcb and use...
I want to use CONFIG_UART_0_NRF_UART instead of CONFIG_UART_0_NRF_UARTE. But I don't get any option for this because CONFIG_UART_0_NRF_UARTE is selected by default .
I...
Hello everyone,
I am working on a project based on nRF Connect SDK v1.7.1 that I want to move to the new SDK v1.8.0. But I'm experiencing problems when building the project...
Hi We'll be adding to a design that uses libuarte/UART0. I've tested/run the example code and it's fine. Changing/swapping index from UARTE0 or 1 works fine as does reassigning...
Hi Sir/Miss,
I use SDK 17.0.2 version and softdevice s112 7.2.0 version to develop in nrf52810.
And, I base on this project (NUS with static passkey) which imports CTS_C...
Hi everyone, I'm developing a program with the NCS 1.8 using NRF52840 and I want to use the SPI, the fact is that I've to connect my device to those pins
And as you can...
