I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
hi ,
i am developing a zigbee network and i have used the the sample project of zigbee light bulb, switch and coordinator given in nrf5340dk. now i am facing issue with...
Hi,
I'm implementing a FOTA update procedure for the nRF9160 using the download_client from the nRF Connect SDK 1.9.1 and modem firmware 1.3.1.
In general the image update...
Hi,
I am using the nRF52840 DK to connect to an external board via the P20 shield debug out. I was wondering if any indication is given if a board is connected correctly...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
The linker script for the example code "Secure bootloader ble" for pca10040 have the FLASH section defined as:
FLASH (rx) : ORIGIN = 0x78000, LENGTH = 0x6000
According...
Hello,
I am using nRF5340 with NCS1.7.0 and nRF RPC lib for intercore communication for our product development. I followed this example ( https://github.com/nrfconnect...
Hello,
I installed NCS 2.0.0 via toolchain manager (Windows).
However, if I:
open a new cmd window
set ZEPHYR_BASE to <ZEPHYR_NCS_2_0_0_PATH>
try to build an example...
For study purpose, I try to change bootloader to move APP offset by
change APP start address to 0x20000
change start_addr in nrf_dfu_mbr_irq_forward_address_set() and...
Hi Team,
I'm using a nRF52810 board for my project but in that when I upload code using development kit, at that time my device give advertising and what I gave task.
...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Hi,
I am using the nRF9160 on a custom PCB, SDK version 1.6.1 and modem FW 1.3.1
My Application uses MQTT to send messages to a server at regular intervals. In between...
I've just installed a new version of nRFConnect for Desktop, version 3.11.1. When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message...
Hello,
I would like to know why Matter cluster Simple Metering (ID : 0x0702) it is not proposed by the ZAP Tool and by the CHIP Tool. How could it be possible to use this...
Hi - I am unable to commission my NRF-5340-DK as a Matter device using the Android Chiptool app.
I am using the matter sample Light Bulb with v.1.9 of the NRF SDK. The sample...
