I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am developing on an nRF52811 and I've noticed that I can't set/clear the pins such as the ones in the bracket in the picture below.
I'm using nrf_gpio_cfg_output(pin_num...
My product is devloping in nrf52810 with Zephyr . The flash is too small. At present, using all peripherals, the size of app_update.bin is 55KB. The size of MCUBoot partition...
Hi,
I'm a beginner, I want to do a test that will create a thread by "K_THREAD_DEFINE" marco.
Then I will continuous print "Hello~~~" per second. That's all.
But I don...
Hi everyone.
I'm approacing to the nrf52833 SoC following this official tutorial but when I import the example template the VSCode finds the cmake tool in my espressif ...
Hello,
SDK Version - 17.0.2
Mesh Version - 5.0.0
I'm using nRF52840 DK to build mesh example(light_lc_server & scene_client).
I try to save the scene of the...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 I have two quick questions. 1) How to add version information(string) when make binary. 2) How can I read version when I finish...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
