I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello All,
i have a problem when I try to change the Bluetooth Address.
This is the code that works correctly: err = bt_addr_le_from_str ( "DE:8B:49:00:00:01" , "random...
Hi,
I did recently start with my pcb design for the nRF52811, but I have some questions about the antenna. I want to use a 2450at18a100 chip antenna of Johanson Tech.
...
Hi,
I am using the nRF9160 in a datalogging product, logging environmental sensors and sending data via MQTT over a LPWAN network. Something that I have noticed for a...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with a connection to an external MCU (#define MQTT_MESSAGE_BUFFER_LEN 8192) We need...
Hi !
in https://infocenter.nordicsemi.com/pdf/nRF52840_PS_v1.7.pdf specified operation frequencies
"
The IEEE 802.15.4 standard defines 16 channels [11 - 26] of 5 MHz...
Hi, I am developing an application that includes the following features: 1. PWM to control the buzzer 2. 2 Uarte to communicate with 2 external devices 3. BLE to wireless...
Hi, I am working nrf52832.
this is a example for sdk nordic and i want to know why when i include a byte (value 0x00) in the m_beacon_info, this data is not reflect on nordic...
Hi,
I'm working on a project using BLE via s140, everything works fine until I look more seriously at the current draw of the device.
Simply, my project starts a Scan...
Hi, In the documentation I read at uart_rx_enable a timeout setting in Microseconds . Under uart_rx_enable_u16 the timeout is defined in Millisecond .
Do those really differ...
Hello,
I'm new to Nordic Zigbee solutions and where to find information so hoping someone can point me in right direction.
Using 2 nrf52840-DK boards. One is flashed with...
Hi, I am trying to follow the nRF Connect Fundamentals course and have just built the Blinky app. It actually builds fine, but on the console it does show that there is 1...
The nrf52 is waking from a sd_power_system_off() and resets. The reset reason register indicates it was from a DETECT from GPIO, yet the LATCH register is 0 and all the sense...
Hello,
I'm writing my own UARTE library because I need some functionality not offered in the SDK. But I came across a hardware behaviour I can't explain.
In my understanding...
Hello,
Right now our application developed using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip.
Need help on migrating to BLE 5.
Which SDK & soft device...
