I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
HI
I would like to check if it is possible to setup 3 sets of nRF5340 Audio DK as a master with two slaves.
Where the master and salves are able to send audio (via mic...
Hi All,
I would like to know how Nordic's pairing mode corresponds to the bluetooth specification.
If my smartphone(initiator) is keyboard display,and my slave(responder...
Hi,
After making a 802.15.4 poll request for data and receiving an ACK message which is not followed by any data message the confirm callback never occurs. I have verified...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I would like to update SoftDevice from v7.0.1 to v7.3.0. Are there any areas...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I have trouble with DFU. I could implement SMP server into my project according to your guide. (+) Add DFU support to your...
Uns NCS v1.9.1 and VSC, I am attempting to run through the Device Firmware Update (DFU) with MCUBoot bootloader exercise.
I am running to a road black in figuring out how...
I have a Bluetooth device that has a long characteristic. On previous central device projects there is usually a function like read_long_char. I am trying to get a zephyr...
We've built a device with the nRF5 17.1.0 SDK on nRF52832 which operates as a HID keyboard. On iOS and Android this is working fine, and it's working fine sometimes on Windows...
Hello, trying to get v1.9.1 lte_ble_gateway working on Thingy 91. Using Thingy 2020:23 1.4.0, which works all good with zip thingy91_fw_2022-02-17_ec486dab (tracker, nrf cloud...
Dear community,
After a lot of though and fighting with our hardware we decided to use a dual slot bootloader config with an external flash.
We based our testing on...
Hi,
I have a C++ class with code as in below:
This I need to call in a .c file, which I did with extern "C" definitions with a C wrapper as in below:
I am getting...
Hello everyone!
I am trying to add a SPI Master instance for my custom PCB, im using spi example as reference but im having a specific problem, and it is that the program...
Hi, We have custom board files (copied from 5340dk dts files) and I wish to remove all redundant DK stuff from my DTS and free up pins. Can I remove UART0 from both the app...
I have gone through the Nordic Academy to install the tools and build the first example which is blinky. I am using MS Visual Code and SDK version 1.9.1. I have seen some...
Hi,
I use serial port example to do out UART exchange data function. But I get a problem, I don't know why? Below is my source code.
When I send 2 bytes data to...
