I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi
I need to read the Drive mode of how an output pin has been configured....
I see that there is an API to read pin's Pullup, Direction, Sense, etc configuration.....
Hi,
I want to make an emitter and a receiver for AOA. I have seen that the example i have to use is " Direction_finding_connectionless_tx (and rx)" but when i open it on...
Hi,
I'm using two UARTs on nRF52840 with SDK17.1.
My issue is both UART works individually until they receive messages at the same time. Both of them receive an RX overrun...
Hello,
NCS1.9.1, VSCode, peripheral_lbs
nRF5340-DK got error:
undefined reference to `z_impl_k_busy_wait'
nRF21540-DK and nRF51840-DK work well.
Best re...
Hi,
I was measuring the time it takes to boot to my application based on the nRF52832 and the time I measured was excessively long.
I'm using a PicoScope DSO for observing...
Hi,
I've been requested a feature regarding buttonless OTA DFU that I'm not sure if it's feasible or advisable to implement.
The feature is that once the OTA is successful...
Hi,
I do not know how to reliably get size of arbitrary UDP data received by #XRECV or #XRECVFROM.
It is clear for text data, but for binary data both #XRECV and #XRECVFROM...
Hi everyone,
I have a preblem for BLE Mesh 5.0 version (board is nrf52840),
I found that in the Setting set function of the Sensor Model, it seems that the data is transmitted...
Hi, I am using Zephyr and want to use the nrfx_timer_compare functions. It seems that the system is working with Timer4 and channel 0 to 4. However, the compare of channel...
Hello,
I have many board of nrf9e5 IC's,
But in nordic company it's discontinue,
It had long range and easy to set,
Now which product is like this?
I need part number...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Hi
I have combined the ble_app_uart and libuarte example. The combination works "nearly" well.Transmit is ok, but when receiving characters over UARTE, no NRF_LIBUARTE_ASYNC_EVT_RX_DATA...
I see a square hollowed out area in the middle of the newly released questions about nrf5340 audio DK PCBA. What is the design purpose of this hole hollowed out area?
