I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello Team,
We are in process of verifying Long Range on nrf52833.
Setup: nrf52833 + ncs v1.8.0
We have developed an Long Range (CODED PHY) advertisement sample and...
Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Hi,
we got a nrf5340 audio DK recently, when want to build example code for it, I get this message：
warning: attempt to assign the value 'y' to the undefined symbol HW_CODEC_CIRRUS_LOGIC...
Hi,
I'm having issues debugging a case where the device is reset / rebooted every 1-2 days on average for some reason without any error message as to why. If any error is...
After successfully building and running the nRF9160 at_client sample app on Monday, I tried to repeat this success this morning but VS Code under Connected Devices says nRF...
Hello!!
I have explored extended advertising using both nRF5 SDK and nRF Connect SDK. Using nRF5 SDK, it is not possible to advertise 1650 bytes in an extended advertising...
