Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
Hi
I use in my project Zephyr ssd16xx driver with Waveshare epaper and LVGL and everything seems to be OK, but there is a strange behavior, when the e-paper works longer...
STEVAL-STMDLTE WITH NRF52840 using UART
We are trying to integrate the STEVAL-STMODLTE Link chip into the NRF52840 for rapid prototyping.
Trying to interface nrf52840...
We notice that upgrading from nRF Connect SDK 1.8.0 to 1.9.0 was generating issues in our application. Now we notice that nRF Connect SDK 2.0.0 is dropping the Segger supprt...
how to get started with nRF_TWI_MNGR , for CTP , touch screen driver FT6206 , what are the necessary steps to follow . what are the call back functions in the nrf_twi_mnrg...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I'm using nRF52832 and the SDK version is "nRF5_SDK_17.0.2_d674dde" ,
First I tried DFU over UART using \examples\dfu\secure_dfu_test_images\uart\nrf52832, and...
Hi,
I build the smp_svr sample for nrf52dk_nrf52832. I installed Go on my windows machine and I am able to run the mcumgr tool. When connecting Teraterm to the UART of my...
Even if i did the configurations i got this error because of the manifesting stage.
When i did the configurations which is like below,
west config manifest.group-filter...
Hello,
I am trying to use Direct Test Mode example on SDK v17.0.1 to do our product's pre-production RF tests. I can see expected results on nRF Connect Direct Test Mode...
Hi, While testing the new nrf5340 Audio DK and BIS example, I wanted to see how the Periodic Advertising Sync Transfer (PAST) data looks on the nRF Sniffer version 4.1.0....
