Hello,
I have run the GATT throughput example to test the throughput for a long range. My test configuration is as below:
ATT MTU: 247
Data length: 27
Connection...
Team,
I am using nrf52810, sdk 17, sd112.
I have setup a write characteristics, to receive some long data ( 64 bytes)
// write char memset(&add_char_params, 0, sizeof...
Hello,
I have a BLE peripheral device that becomes the server once a connection is established. The BLE services and characteristics are all custom, I will include the defines...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hi All,
I'm using nrf Connect SDK v1.7.0 with Vs Code
So here I can see in the debug prints that Bluetooth device is able to get connection successfull callback and Immediately...
Hi everyone,
I have a preblem for BLE Mesh 5.0 version (board is nrf52840),
I found that in the Setting set function of the Sensor Model, it seems that the data is transmitted...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
Hello everybody,
we are currently working with an nRF51822 mounted on a Adafruit Bluefruit LE UART Friend. We use pca 10028 and s130.
While debugging through the code...
I am developing for a Thingy91 and NRF9160 DK
NCS v 1.9.1
I was initially using the LTE_BLE_Gateway sample with the NRF52840 running the hci_lpuart sample. and that...
Hi Devzone
Currently for my customer request , they would like use the nrf91 on their wearable.
They would like to do NRF91 FOTA with the external flash SPI w25q128jv...
Hello,
I use ncsv1.9.1 and segger embedded studio.cmd to open a nRF connect SDK, but there is an error: S yntaxError: Unable to parse JSON string .
I replace SES and...
Hi, My current application is using a softdevice and I need to update it using DFU to an application without softdevice.
The new application must start at 0x0 address, so...
Hello guys,
I am using the nRF52 DK.
I have to connect a spi sensor which is already made.
This part works. ("nrf_drv_spi.h" fyi)
I also have to store the info...
Hi, I'm using the Adafruit ble sniffer (V2.0, black board), with the nRF51822, and I can sniff on wireshark (3.6.5), with Nordic package 4.1.0 (python 3.10.4) The problem...
Good day I am wondering if you can help me.
For background information.
Network - NB-iot
Firmware - 1.3.1
Software - Serial LTE Modem
Hardware - nrf9160dk
...
