Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
Hello. We are preparing production. So I have to provide flash tool as well as binary only to factory without develop...
Hi there,
We are trying to enable the interrupts on one of the UARTE peripherals, and are having trouble finding the interrupt number within nrf5340_application.h? It is...
Hi Everyone,
The custom device I am working on is a BLE peripheral device and uses softdevice S132,
therefore to get accurate triggering of ADC sampling and to avoid periodic...
Dears,
We are MCU Programmer Supplier, now we are developing the off-Line Programmer for NRF5340, and encounter some problem as below:
1. Does the Nrf5340 Flash Memory...
I have a custom model server that sends 8 bytes of data
I set up 2 nodes - one to publish to an address 0xC002, one to subscribe to publication
Provisioning and publish...
Is there any documentation/tutorials for using NRFX drivers directly in Zephyr without trying to create conforming device drivers? I have a lot of code written for the NRF52840...
We have a board based on the nrf9160dk.
The project is essentially based off the "LTE sensor gateway" project with hcl_lpuart to utilize the nrf52840 for BLE. Chip shortages...
Hello,
I am performing garbage collection. During the garbage collection an event could be fired (from the softdevice) that causes updating of records.
My question is...
Hi
I would like to know, if Zephyr-s ssd16xx driver supports display driver board power supply control? I see from Zephyr documentation ( solomon,ssd16xxfb (on spi bus)...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
