Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
I have shell working with the following configuration
CONFIG_SHELL =y
CONFIG_SHELL_BACKENDS =y
CONFIG_SHELL_BACKEND_SERIAL =y #also selects serial
CONFIG_SHELL_CMDS...
I downloaded a project in named prj9160 from Github. The prj9160 had three folders : Azure, firmwre, mscerts. I run successfuly the following command :
west build -p always...
Hi everyone,
I want to run nrf_drv_saadc_sample in a loop but I do not want to use PPI and TIMER peripherals because they increases the power consumption of my device. I...
Hi , am working on mesh example from v1.8.0\nrf\samples\bluetooth\mesh\light_switch. In this example they are using generic on/off server , light LC server and other server...
Hi.
For example, for the nRF52832 BLE chip, could it, in some manner, be only visible/communicate with a specific/particular smartphone app? How? using the MAC?
Regards...
Hello, I have a nrf5340dk communicating with nrf52840 dongle connected to a pc with UART baud rate of 2M. Connection parameters are:
7.5ms Conn interval
1ms Slave latency...
Background The adxl362 driver native to the zephyr kernel doesn't support FIFO operations, so I built my own out-of-tree driver that relies on a new accelerometer API instead...
I wish to add a firmware version to my project. Because we are hoping to use OTA for updating I have set the configuration paramater:
CONFIG_MCUBOOT_IMAGE_VERSION
in proj...
After working with arduino's and microprocessors like the ESP8266 and ESP32, I recently started toying around with a nRF52840 dev kit. After going through some tutorials,...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
Hi, I have a problem configuring the PPP Modem correctly and I'm not quite sure what i'm missing here.
I'm running the code on a custom board. We are using nRF52832 to talk...
Hello dear!
1- What is the relation(formulas) between current in uplink I uplink and the data packet size?
2- What is the relation between the iDRX PDCCH repetitions ...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
Hello. I am setting up the nrf9160dk and when I got to the step when I had to activate the SIM card. When I had to fill up my address etc. it didn't let me save it so I was...
Dear Sirs,
I have a sensor working as a peripheral and using the Nordic NUS service. I have a poblem discovering the two MSBits of the sensor's address when it connects...
