Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
I am new to Zephyr and I have been trying to get hold of a tutorial or a sample app that would indicate how I can use the UART on the nRF52832 for communications with another...
Hi,
I'm wrapping up a project which uses an nRF5340 as both a Bluetooth peripheral to advertise etc and also as a Bluetooth central to scan for devices (not both at the...
I recently started development on NRF52833 for one of my projects. I use segger embedded studio with the " ble_app_uart " example. As I mentioned I'm using nrf52833 DK so...
I want to recover DFU over BLE upon a dropped connection while in the middle of an update.
I have my own software that I've cooked up to program from another NRF52 chip...
Hi,
I see you have what appears to be a working implementation of OOB/NFC pairing over iOS here ( https://github.com/NordicSemiconductor/IOS-Nordic-Thingy ), which doesn...
Hi,
Here is my previous ticket.
https://devzone.nordicsemi.com/f/nordic-q-a/83856/channel-interference-at-nrf52840
I haven't had response tho that's why I made a ticket...
Hello! We have an application that I need to implement Tensorflow Lite. We started with the Arduino Nano 33 BLE Sense board, which had a TFL library on it. After using it...
Hi,
For 52820-QDAA, what load impedance is preferred seen into the matching network? I mean the total load impedance of C3, L1, C4, L2, RF trace and antenna.
Since our...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
