Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
I working on Asset_tracker_v2. I need to add event based custom module to the application Asset_tracker_v2. I created follwoing files:
A. In the src/events folder
1. bms_event_module...
Hello,
I am new to Zephyr and its ecosystem which includes MCUboot and also the NCS sdk. I have a question regarding the nRF5340 bootloader.
So we already have a product...
I had to upgrade SoftDevice and application firmware from v6.1.1 to v7.2.0 in order to have BLE_GATTC_OPT_UUID_DISC option available.
It turned out that Bootloader needs...
Hi,
I want to implement a BLE function that a master can connect to multiple slaves at the same time，and the services are located at the master，do I need to create multiple...
I'm having some (minor) trouble with a board based on an NRF52840 that I want to start running as soon as power is applied...
This is built using a RAK5010 board, but using...
So I just got past the hurdle I had when trying to do extended advertising in the following support thread, and now I have a new problem along the same lines:
https://devzone...
Hi All,
We are planning to use MAX 3051(CAN Transceiver) which will be interfaced with the NRF52832 over UART.
Our goal is to decode the incoming CAN messages from the...
I had been using the Andoid 4.24.3 version of the nRF Connect app and had no problem with performing DFUs. With the newer 4.25.1 version of the app I noticed a few things...
While trying to reply further queries, by mistake, above ticket got closed ... So, I need to discuss more to the reted issue in the ticket. When, there is a click on verify...
Hello,
I'm trying to add credential to the modem on the nrf9160. However, i keep getting a -111 error when i'm trying to connect to my server with TLS mode.
When i try...
Hi
I connected the nRF21540 to a nRF52840 like in the application notes.
Here is the schematic:
I implemented the driver and now I try to communicate over the SPI...
Hi
I'm using the PA LNA driver for the nRF21540 with the function:
void mesh_lna_setup_start(uint32_t rampup_start_capture_time, uint32_t timer_index)
Now, when I check...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
Hi team !
I'm facing issue when porting my code from nRF52840DK to nRF5340DK
I implemented SAADC acquisition, using Timer/SAADC/(D)PPI stack on both boards, handling...
