Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
hello,
i had read mac id of nrf52832 using python and adalink. Now my window is updated from window 10 to window 11
so i have to reinstalled all setup while reinstalling...
Hi,
I have been using the PPK2 with older software (nRF connect for desktop 3.7.?) on Windows 7 64bit.
Initially all was working correctly then on the next day, the Power...
Hi
I just started using VS with Nordic and keep getting the error below can someone please assist.
Debug session did not terminate cleanly TypeError: Cannot read property...
Hello i am using nrf52810 with SDK version 17.0.2 , i want to add custom service to the ble_app_template example and i followed this tutorial link https://github.com/edvinand...
Hello, I've been trying to run both Blinky & Hello_WORLD examples given with NCS 1.6.1 on an NRF9160-DK but I don't see any output. I was able to build & run successfully...
Hello,
I found that the 9160 is certified with Verizon based on this page: https://www.verizon.com/about/sites/default/files/Nordic-Semiconductor-IOT-device.pdf . The Fanstel...
Hi
When DC/DC is used with REG0 or REG1, an external inductor is required.
The recommendation is "10 µH Chip inductor, IDC min = 80 mA, ±20%".
However, the lack of information...
Hi All,
I've run into a weird issue where my SPIM rx buffer remains empty (it's not even filled with garbage - just empty). Am I operating the SPI drivers properly? My...
Dear,
When I try to use <nRF Connect for Desktop>, it will show this message below:
I checked, this is because the first web which is based on America, can not be opened...
Hello, we are currently using the nRF51822 chip, and have roughly 1000 units of this particular device out in the field. After a few months of use, approximately 20 of these...
Hello,
I came across a very consistent bug that occurs on the nRF9160DK and a custom board with an nRF9160.
Basically, if you try to send the AT commands "AT+CFUN=1...
Hi,
I'm working with Nordic nRF52832 and trying to install Nordic Semiconductor nRF CPU Support Package from SES, from Tools--->Package Manager.
However, I wasn't able...
Hi
I want to use the NRF52840-DK board to evaluate some circuits that communicate with the nrf52840 chip. I want to design the board to act as a header for the hevelovpment...
