Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
I've just received nRF52840, it powers up and blinks as programmed and the buttons work. I hear the "ba bing" on my PC when it connects and disconnects, but the JTAG does...
Hi DevZone,
I need to change some defines in the ffconf.h file used by nRF5 SDK to set configurations for FatFS to enable use of f_findnext(), f_findfirst(), etc.
Is it...
Hi,
I have provisioned some nodes using interactive_pyaci successfully. Functionality is as expected. As a test, I then shut interactive_pyaci down, rebooted the nRF module...
Our Gateway uses a NRF52 and the sensors a NRF51.
Gateway is outside the freezer at + 20C and the sensor is inside the freezer at -30C.
What we see is the pairing becomes...
I'm working on a wireless musical instrument which requires a super low latency RF link. I previously was using NRF52810 and found that the latency was too high. The complexity...
Hello,
I'm a beginner ... I would like to connect a LoRa module (REYAX RYLR896) to send data from my nRF52840 Express to an Arduino UNO (with LoRa).
I don't know how...
Hello,
I am trying to work with the DFU examples provided with the SDK. My board is a custom USB dongle to which I need to add the bootloader. Following the steps from...
Is there a way to enable LE privacy for nRF52 DK in Bluetooth Low Energy App of nRF Connect for Desktop? I would like nRF52 DK to use resolvable private address when connecting...
hi, Im trying to read from a sensor register using TWIM peripheral on nrf52840 in blocking mode, but it wont work , doesnt freeze or anything .. just doesnt work
below you...
Hello,
I am trying to set system on mode in nrf52840 usb dongle.
This mode switched automatically by idle task, when there is no thread running.
There is no while(1...
Hello,
I m new to nordic in VS code. Bought two nRF5340 DK for ADC conversion and wireles data transfer.
Followed all Youtube install instructions "nRF Connect for VS...
Is it possible to communicate with the of nRF52840 through USB, for example using PyUSB?
If yes, is there any documentation that can help in this regard, e.g. documentation...
These are Central device 52840 settings:
These are peripheral device 52810 settings:
I use official sdk16.0. Central Project is ble_app_multilink_central...
HI,
I am designing a costume PCB of nRF52840-CKAA-R7. I used Johanson 2450AT07A0100 Chip antenna for BLE, please suggest the matching circuit for it.
Due to size concerns...
