Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Ηι
Hi everyone,
I have written a code to sample from an analog input using RTC and PPI.
The SAADC does not start on RTC compare event.
The RTC compare channel works...
Hi,
I have some dependency issues in my devicetree definition.
I have a first regulator that control the power of a gpio expander connected through I2C.
This GPIO...
We've developed an application based on nRF52840 (via Raytac module MDBT50Q), utilizing the Adafruit Feather Express Bootloader as our basis to simplify the development. Our...
Hello.
Log data is transmitted to APP(phone) using sd_ble_gatts_hvx().
The length of one packet is 20 bytes, and the expected total number of packets is about 3,200...
Hi folks,
Looking at the nRF Command Line Tools download page , I can see versions of the nRF Command Line Tools for Linux, MacOS and Windows. The Linux versions come...
Hi everyone, I would like a bit more insight and recommendations around the following list of SDK_CONFIG options. The description is not clear enough and I don't understand...
Hi, I am using libuartes to comunicate with gps and I get the Rx buffer like a problem already asked in this thread when I send a text "abc"
the first 3 times : everything...
Hello,
- If I supply nRF52833 in High Voltage mode (LDO + LDO sub-mode, not the DC/DC convertor).
- Set the VDD in the corresponding register to be e.g. 2.7V (VREG0 LDO...
Hello all,
this is actually repost of the previous post : Porting the library code of the sensor due to my fault, somehow I have clicked on the the wrong button ...
Anyway...
Hi,
Our product is using nRF52810, and we need DFU. But the size of application Bin is over 60kbyte(about 63k). When we use S112(100K), the bootloader is 32K, so we just...
I am using:
nRF52840DK nRF5 SDK for Thread and Zigbee v4.1.0 CLI example with added code Border Router on Raspberry Pi 3+
Using the CLI, I can get an IPv6 address for...
We would like to use the nRF52840 to upload compiled Arduino firmware in hex file to atmega328p over serial port.
The latest version of the Arduino firmware would be stored...
nrf52833, custom application based BLE Central Uart Project.
s140_nrf52_7.2.0
Our average Power use in the application is 1.5mAmps. What is the proper way to manage...
Hello,
We're implementing an application that makes use of C++ std::atomic variables and their associated memory-ordering semantics for inter-processor communication between...
Hi, I am working on ble_app_uart_c(central device) and want to add the DFU option. I have successfully added a buttonless DFU service in the peripheral application. Now how...
