Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hello
I am using the NRF9160 and I can see that modem RF transmitions cause some EMI issues
I would like, for a period of few seconds each time to stop modem transmitions...
Hi, dear Nordic team,
We've already purchased a few thousands of BC805M BLE modules (nRF52805) for our upcoming mass production. During R&D, according to datasheet, we...
I need to use Delay of few Micro/ Milli / Seconds without pushing the MCU in sleep i.e. without using k_msleep() etc. Is there any library for this purpose in Zephyr ?
Hi, Hope you can help. With a nrf52840dk development kit arriving tomorrow. We tried to make a start with a nRF52840 dongle, which we eventually want to use. Connected to...
Hello,
I follow the doc to install the nrf_sniffer_for_bluetooth_le_4.1.0
- Flashing the nRF52840 dongle with nRF Connect for Desktop
Uploading image through SDFU: 97...
Hi,
I'm trying to use a nRF52840DK as a zigbee router implementing a temperature sensor. The setup is composed of
Software
Application: Home Assistant
SDK: nRF5...
Hi, I'm trying to achieve high throughput of BLE on connection between two nRF52840 DK.
I've read some articles about it, and configured both Central and Peripheral devices...
Hi,
I'm looking at the nrf5340 PS v1.2, page 75 & 76 regarding the audio clock PLL. Using the formulae given, I'm finding that the register value that yields the closest...
Very much a beginner at this so if this is inappropriate for this forum do not hesitate to let me know.
Starting out trying to develop a BT Mesh system. I purchased a nrf53...
Hallo Dears,
I would like to develop a ble-peripheral role device with a humidity sensor service. I found the development kits from the nRF5x family such nRF51, nRF52...
Hi,
I'm trying to take advantage of nRF52840 as Zigbee NCP in communicate with a host microcontroller via UART. My problem is I don't know what I have to send and what will...
Hi,
In your LE audio presentation from CES that you had a demonstration of a low latency setup with LE audio. We are more curious about the setup you demonstrated so we...
I have built and successfully run this application with the nRF Cloud and then I achieved a partial success with running this application with the AWS IoT.
When I run this...
Hi there, My nRF52840 Dongle suddenly stopped working. The application that used to work among a few last weeks stopped during one of exploatation. Pressing Reset Button don...
