Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hello,
I use nRF52810 in commercial product. I modify examples (ble_app_hids_keyborard_pca10040e_s112 and ble_app_uart_pca10040e_s112) a bit. If softdevice S112 or the examples...
Trying to build one of the sample applications from the SDK using VSCode and nRFConnect SDK v1.8.0, when attempting to create a new configuration for a project, the build...
Hi All,
SDK => v17.1.0
IDE => Segger
Project => ble_app_bps
I use LightBlue to connect my board,and going down to the device information service I choose system...
Hi,
I'm using nRF5340 DK, one board is programmed as central and 2 boards are programmed as peripherals. When I flash the central program it is selecting a random board...
Hello,
we are currently experiencing issues with the SPI interface which we suspect is due to the behaviour of the MOSI line in idle state. We have noticed that during communication...
Hello,
I am planning to test ethernet module on nRF9160, use SEGGER SDK v1.7.0 for compile the programs. In Q&A I saw using can bus module & ENC424J600 ethernet controller...
Hey,
I try to read the CRC from E-Paper display series 1.02 inch (GDEW0102L4f) with no success (I'm working with nRF52833 Development Kit)
My code and the official Goodisplay...
Hi
I can‘t find the bank size configuration in the project secure_bootloader_uart_mbr_pca10056。 For safety reasons, I want to artificially divide the size of bank0 and bank1...
Sir,
I am using a U-BLOX NINA B302 (nrf52840) connected to a SEGGER J-LINK to program it!
Using the J-LINK flash i can program the NINA B302
But, on VISUAL STUDIO +...
Hello!
I am having 3 nrf5340 devices; 2 Gateways and 1 Headset. I am trying to achieve the scenario where I can allow the Headset connects to selectively one of the 2 Gateways...
I recently got the nrf52840dk board and I am trying to use it with the Nuttx embedded OS. However, I am having some issues flashing the nuttx binary on my board.
this is...
Hi
I am using nrf52832 s132 with s132_nrf52_7.2.0, sdk17
so far have successfully updated application and bootloader with an adaptation of buttonless DFU, now I have an...
I'm trying to accurately measure our 3.0 volt coin battery (CR2450).
Our product consume low power (<50 uA) and we measure the battery voltage every minute.
We must...
Hello,
I've been trying to get through SUPL client library license signup process but I my request get denied every time.
I think I've done everything that is required...
I wrote a firmware on my dk52 and am advertising some data to the nRF Connect for Mobile App.
Is there any way on how I can copy or send the received data (service data...
