Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi,
we have an odd issue on ~ 50% of our in-house boards here. We're using the internal RC as a low frequency clock, and then enable one RTC. No softdevice or anything....
i am using nrf52840 USB dongle and the segger J_LINK EDU mini for debugging when i use bulid and run it works, and if i remove the donle and reinsert it then ts not working...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
Hi,
Here is my hardware.
VBAT is 3.6-4.2V, UWB_EN is Pin28.By using nrf_gpio_cfg_output( UWB_EN ) to init this IO.
Is there any problem?Because when I using nrf_gpio_pin_clear...
Hi,
my product now is base on the nrf5340, I want to set the USB's serialnumber same as the ble mac address.
when I use the nrf52840, I can set it as follows simply. ...
Dear all,
My objective is to have an external MCU send data to an nrf52840 via UART and directly send this data via BLE to another nrf52840. I started from the ble_app_uart_c...
Hi,
I am developing an ANT TX application using the nRF52832 and SoftDevice S332. Things seems to be working well ... but I need one clarification As per the ANT example...
I am running the NRF52832 (BMD-300 module) and I'm trying to talk to battery over SMBus.
SMBus is compatible with devices up to 100 KHz.
I was wondering if there was a...
Hi,
nRF5340_PS_v1.0.pdf has multiple PIDR2 values to denote engineering versions of the chip. This seems to have been removed in subsequent product specifications, and now...
