Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
This ticket is related to an old unanswered case ( Openthread otUdpSend transmit finish ). I need to send a large UDP message in chunks and therefore need to be able to tell...
Hi,
I am working on setting up multiple ADC channels in the device tree. My starting point is here , which seemed to be an unofficial ADC example that many ADC-related...
Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
For power optimization I did to disable Mesh Using this piece of Code
and Re- Enable using this code
So the Real Question is that , After disabling Mesh for some time...
Hi
I need a suggestion. We are like to try a long-distance I2C communication between the sensor & Nrf5340 that is we need to connect 1.5 meters of cable between them. So...
The device advertises.
The phone scans.
The device use white listing and only allow one peer, the phone.
What's the difference between erasing bonds and disabling white...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
Hi,
I'm using nRF Connect SDK v1.7.0 to develop a firmware for a custom board with a nRF52832 MCU. I'm using VSCode to build and flash my device using the nRF Extension...
Hi All,
My dev environment is as follow:
nRF52832(Central) + S132 + SES + SDK 17.0.2
Normally my Multilink Central code is flashing and working properly without...
I'd like to know of an example(s) for interfacing nRF52840DK board as a Master SPI to an Arduino badge (from Honeywell). I have the badge working with an Arduino Uno (Rev...
Hi,
If I want to use the NRF52833 as TX, and NRF24LE1 as receiver. How I can I match out the address?
If NRf24le1,
RX_addr = {0x00, 0x 11, 0x 22, 0x 33, 0x 44}
then...
Hello,
I'm working with NCS 1.7.1 and the nrf52840 dev kit to implement a BLE peripheral with FOTA, stats and configuration features. I've added MCUMGR to the project so...
Hi Sir,
As we know the inductor connected to the DCCH pin is a DCDC function for high voltage mode.
But what side effect we can see if we connected the inductor at the...
Hi,
I'm using NRF52840 to connect to an Android mobile phone.
The application scans for advertisement and when the NRF device starts advertising - connection is established...
Hi,
I'm evaluating the performance of the Zigbee protocol implementation on the nRF connect SDK using nRF52840dk:s. nRF connect SDK 1.7.0, ZBOSS I'm not sure where to find...
Hi everyone,
We are using the secure bootloader in our board, and we are adapting that bootloader for our requirements. Moreover, we use the DFU updates for our Main application...
