My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
I am not sure what I am missing in this. This is a custom board so there is no other circuitry on this pin other than a pad to monitor the signal changes with.
When...
Hello!
Regarding the CRC on the nrf52840 the specifications make it clear that the maximum length of the CRC is 3 bytes, We are working on an industrial communication protocol...
Hi
How can I readout the actual timer value on the fly? I use the timer in capture compare mode and like to read out the timer value.
nrfx_timer_clear(&m_pyq5848_timer...
Hi all,
I have set up an nrf52840 as the sniffer to sniff the connections between my custom board and central phone. My goal is to figure out the bottle neck of the ble...
I based my project on the secure wireless uart example in the nrf5 SDK and linked to the precompiled gcc library 802_15_4_lib_gcc.a
I then tried to add multiple entries...
It seems that once we install nRF Connect into VS Code it completely takes over and now when I open any file in VS Code I see all of the nRF connect tabs and controls which...
I'm trying to debug an application however there is no documentation on how to set up the debug.
How come nRF connect is selecting the HEX file. I want it to select the...
Hey,
I am trying to use the Jam Detection Feature of Openthread on my nrf52840 DK. The device is running as coap server with the example code
"simple coap server". I...
Hi,
Is there any tutorials or examples avaialble for adding DFU service? I would like to add DFU service for my application. I am using nRF52840 development board with...
Hi All,
I'm using SDK17.1.0 and I have a question about pairing.
I have a project that references the ble_app_bps program, but I don't get pairing notifications when...
Hi All,
I have a question, it seems to be the SES debugger crashed.
My project only uses peripheral devices, my purpose is to combine libuarte with my framework.
And...
I want to send an interrupt instruction from appcore to netcore by using IPC.
Implementation code in appcore:
Implementation code in netcore:
However, in actual...
I have a vendor mesh model that needs to send a custom 8 byte message.
Here are some definitions
BT_MESH_MODEL_PUB_DEFINE (vnd_pub, NULL , 3 + 8 ); <--what is with this...
