My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I tryed to reduce the power consumption of my beacon (ble_app_beacone example from SDK) to have more battery live. To do this, I want to reduce the TX power. And also change...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
Hi,
I'm currently using nRF Connect SDK v1.9.0 and developing on a nRF52832 onto a custom board. I'm using a BMI090L from Bosch connected over i2c.
I'm trying to suspend...
Hi.
Encountering an intermittent issue where, after a DFU (either OTA using Nordic Device Manager or over usb serial using dfu-util on Linux), the image is reportedly in...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
In the DTS file for I2C, how do you set the port of the pin specified?
&i2c0 { compatible = "nordic,nrf-twi"; status = "okay"; sda-pin = <26>; scl-pin = <27>; };
In...
Hi,
I have a question about the whitelist，when we use the function "pm_whitelist_set()" to set the whitelist，whether the whitelist is stored in RAM or FLASH? I traced the...
Hello,
I am using nrf52810 with custom board and i have created DFU for uploading a OTA file previously its working fine but i don't know what happens now BLE is getting...
Hi:
When i read data from the device nrf52833 to android app, only get 600byte data and it should be 4096byte. The app use the Android-BLE-Library-2.4.0 lib.
The nrf52833...
Hi,
I have a question on SDK release plans. There is a change awaiting for release (merged after 1.9.1) and it would be nice to develop them with an official release, including...
Hello!
We are two students working on IO-Link Wireless as a bachelor thesis project. Our task is to make a Wireless Master prototype using the nrf52840 DK kit from nordic...
I am making a ble beacon application. I need to send more than 30 bytes of data via advertisement. How can I do? Because UUID data will not be enough for me.
Hello everyone and hello kindly nRF support team!!
One question again sry. I am using SDK 1.9.1 through VS Code and working on the nRF Connect SDK Tutorial - Part 2 -...
