Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hello,
I am using s112_nrf52_7.0.1 I have the nrfRF5 SDK and I built a custom application using BLE.
When trying to test it I use the example ble_app_hrs and it works...
On the nFR9160, the modem is drawing more power when it can't connect to a tower and is causing the battery to drop below the rail, causing our device to switch off. Is there...
Hi,
I discovered that when I use the 'write' button in the nrf connect programmer, that it completely overwrites the whole program (similar to erase&write). Before I didnt...
I am developing a proof of concept for a device however I have some questions regarding the Zephyr display libraries, I have a wave share display with no driver such as SSD16XX...
Hi, Is there a limitation on the available MCLK frequency for the NRF9160 I am trying to configure I2S master with 16K sampling, 16bit, and after i2s_configure() SDK info...
Hi,
I am now working on communication part between esp32 and nrf5340. I want to send the data via ble from nrf5340 and it will receive by esp32. Now, I can able to connect...
Hi sir
We're now working with the nrf52840 DK board, and we want to use two i2c at the same time, but I'm having trouble with one i2c working properly, which means twi1...
Dear Sir.
I use these commands to connect the Modem ON and OFF.
I need to know if the result of the these commands the Modem communicates with the Cell tower ?
Please...
Hi,
I have nrf52833-DK. Where should I get started for DOA applications? I'm experienced with other nRF chips, but not for DF and RTL applications specifically.
Hi team,
I would like to stream(through USB) data every 10millisecond using RTC interrupt.
is this possible or should i use other timers for this purpose ?
Can i configure...
Hello,
I try to debug a BLE connection with the nRF Sniffer. As a test, I used one nRF52 DK (PCA10040) as peripheral using nRF Connect and and Android phone as central device...
I'm using the HID keyboard as the base example. We're using prototype hardware so the connection gets dropped periodically due to ongoing hardware issues. But this has exposed...
Hi, nordic Engineer!
Merry Christmas！ I am using the DF to develop my project and considering simulation with the Bluetooth signal with antennas to build a customized antenna...
Hi,
I am trying to receive messages via Bluetooth mesh and forward them via UART (using UART async API) on the nrf9160DK. But when I try this, I get an assertion error from...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
