Im building a wireless sensor network for farming applications and the issue I face is that when I supply the nrf52840dk from the external supply pins (P21) I get like 25μA...
We have a device that works correctly on iOS, Android, mac, but disconnects on some Windows machines. We use nRF5 SDK 17.1.0 and s132 7.2.0. The disconnect occurs after the...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
Hello,
I am using an nrf5340-DK board and the SDK 1.9.0.
I want integrate the FOTA functionality into the example which was provided by Nordic Semi:
nRF Connect SDK...
Hello all,
referring to this tutorial https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentSortBy...
I want to change the connection params in peripheral role with nrf52840 without informing the central device to do the actual setting operation, yet I don't find a relevant...
We have been looking for a standard (in Zepyhyr or SDK) way of handling communications between our software modules (drivers, modules, threads) that generate multiple streams...
I am just getting started with the Nrf52840 dongle and trying to flash a few examples from the SDK. I was able to flash the "blinky" example just fine using the programmer...
Hi,
I have been trying to interface GSM modem with nRF52840 using LPUART (nRF Connect SDK). I have used below pins for connections:
nRF52840 - GSM
P0.21 (TX) - RX
...
Hello,
Now I am developing firmware for nRF5284 DK, and the one of the requirement is the voltage keep in 2.1V.
Is there any possible I can modify the voltage to 2...
I'm working on a BLE application based on the Zephyr RTOS. I need to read a SPI device at fixed time intervals and, as already suggested me here at point 3, I'm trying to...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
Hi guys,
I'm thinking of implementing consumption optimization on a system that runs on nrf52832 with S132 SDK 16.
The idea is to call nrf_pwr_mgmt_run() to put our...
Good afternoon,
I am working with the NRF9160-SICA-B1A-R module on a custom board.
Checking the functionalities with a software developed on a Thingy:91, I get the following...
Hi, I have recently upgraded to a new system with windows 11. I have been working with NCS v1.8.0 on last system and installed the same in new system. all the necessary installations...
We are developing a custom device based on the nRF9160 SiP Revision 2 with multiple connections over LTE-M and we are experiencing problems with keeping our only TCP connection...
I have downloaded the WS2812 driver example and have successfully been using the nRF52832 DK to control these lights with SPI. I am ready to start developing on a custom board...
This was driving me crazy. nRF Terminal extension in VS Code just silently fails. I was able to use the JLink Viewer app so I knew RTT was working correctly.
I then looked...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hello,
I am using an nrf5340-DK board and the SDK 1.9.0.
I want integrate the FOTA functionality into the example which was provided by Nordic Semi:
nRF Connect SDK...
Hi, I am using nrf52840 to senda imu data over bluetooth to computer. For the transmitter i am using NINAB306 with integrated PCB antenna as a central i use nrf52 dongle....
