Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hello Nordic Team,
I have a nRF52833 DK with me.
I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
Hello,
What is the difference between 2 devices which are constantly scanning and 2 devices which are connected? Also, how do I code 2 devices to connect to each other?...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
Hi.
I'm working with an NRF5340DK using NRF Connect SDK in a project where I need to decrypt an input text with a previously adquired key usign AES128 CTR, but I've been...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello, I tried to upload a simple blink sketch from pca10040 which works for nrf52832 to an nrf52810. But it didn't work. Then I tried pca10040e. It worked for nrf52810. ...
I accidentally clicked verified answer while trying to edit the page.
https://devzone.nordicsemi.com/f/nordic-q-a/87116/apply-the-heartbeat-publication-and-subscription...
I want to be able to send the "AT%" type of Nordic proprietary commands to the modem (and read the response back) via firmware on the nRF9160. I know about the
nrf_modem_at_cmd...
Currently I have been able to advertise and connect through debug app using nRF52 DK. My target is:
1. After the link is lost the bluetooth gets disconnected and at this...
I have been using Segger Embedded Studio to develop in and recently switched to use VS Code with NCS. It was always very useful to use Segger's watch window with the real...
Hi All,
I want to add pairing and binding functions to the blinky project.
But nothing happens when I connect.
Please help me,thank you.
Here is my project =>
...
There have been several posts, all with issues and work-arounds. When does Nordic intend to have MacOS M1 support for the entire development toolchain (including native VS...
Hi,
I just tested an SPI loopback example on nrf52833 board from the bellow code
https://elixir.bootlin.com/zephyr/latest/source/tests/drivers/spi/spi_loopback/src/spi...
I have an nRF52840 dongle I got from someone else that doesn't have the nrf bootloader on it. When I plug it into a USB port, the red light flashes quickly while a green light...
hello,
i have downloaded ( BSEC ) library from https://www.bosch-sensortec.com/software-tools/software/bsec/ for read sensor data . now want to test the code by build and...
I am using the latest code(v1.9.0-rc2). The board is nrf52833_nrf52833. The board overlay file set antenna number to 13. (The original value is 12).
It seems that...
Hi,
I'm trying the USB Audio in ncs .
dts is like below:
And prj.conf:
CONFIG_USB_DEVICE_AUDIO=y and other USB relevant defines.
It works,and the usb audio data...
Hi,
i upgraded the nRF Connect SDK from 1.8.0 to 1.9.1. During the install i have chosen a different install path - to have the same current path in different locations...
We were developing an nRF52840 device and were working on MCUBOOT DFU firmware updates, and accidentally did an update rather than an upgrade, and now my nRF52840DK is bricked...
