Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
Hi.
I'm working with an NRF5340DK using NRF Connect SDK in a project where I need to decrypt an input text with a previously adquired key usign AES128 CTR, but I've been...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi there,
We are intending on using the serial LTE Modem example on our nrf9160 with MQTT. What version of MQTT is supported on this example?
Kind regards,
Frikkie
Hi,
I have been using I2C code for almost a year to talk to a variety of sensors with complete success. Typically, we have used a Nordic BL654 module that includes an nRF52840...
I'm getting a strange amount of error when trying to measure the battery for a custom PCB based on the nrf9160.
Details
My VCC_IO is 1.8V
My max battery voltage is...
Hi,
Perhaps I have a misunderstanding of this GNSS Socket Option.
In the GPS Sample Project (samples/nrf9160/gps) with a nrf9160-dk and no connected GPS Antenna, I set...
Hello, I am trying to add a watchdog timer to my code which consists of THREE threads, so I referred to the task_wdt example in Zephyr/Samples/Subsys for SDK1.6.1.
Based...
Hi,
I wonder if there is a smart and easy way to implement a fallback if I use the MQTT connection with a static IP. What I want is if the IP fails to connect it tries again...
this error shows after the 100% completion of memory flash as shown in the screenshot below. after showing the error , nrf52840 pulsing led turns off automatically.
Note...
Greetings All,
I am trying to connect an nrf52840dk board to an nrf52840dongle for wireless serial communication.
I flashed the nrf52840dk with the central_uart sample...
Hello,
I am using nrf52832 and i am using a SW similar to the beacon.
I tried 2 configuration:
tx_power = 0 (0 dbm)
tx_power = 4 (4 dbm)
I tried to measure the...
Hello,
I'm familiar with the GPIO and GPIOTE peripherals,
The GPIOTE has 8 channels, so it can use 8 GPIO pins to fire interrupts.
Some questions:
- Can the 8 Channels...
Hi ,
I have compiled in Heart rat relay into my app; can scan and connect to simulator and garmin HR straps; but fail to connect to polar. My debug log shows...
...
I've successfully built the 'direction_finding_connectionless_tx' project and flashed that to an nRF52833dk, and built the 'direction_finding_connectionless_rx' project with...
Hi,
I'm using a NRF52811 on a custom board and I would like to change a project from a NRF52832 with S132 to it.
I only use supported functions from the S113, but I...
how to set the High-drive QSPI?
NRF_GPIO_PIN_H0H1
nrf_gpio_cfg ( mosi_pin ,
NRF_GPIO_PIN_DIR_OUTPUT ,
NRF_GPIO_PIN_INPUT_CONNECT ,
NRF_GPIO_PIN_NOPULL ,
NRF_GPIO_PIN_H0H1...
