Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi, after adding some functional to bootloader an error occurred: section .tdata overlaps absolute placed section .mbr_params_page how to calculate the size need for mbr_params_page...
We have a 52840 based beacon with two versions. Both have exactly the same firmware and PCB, one has a N52840-Q1AAD0-2025KR written on the chip and the other has N52840-Q1AAD0...
Hello!
Im having problem running the PPK II on my PC with Ubuntu 20.
The device attaches to the PC, is visible as `/dev/ttyACM0` block device and dmesg shows no errors...
Hi,
I am using as settings:
timeslot period: 600 us
data rate: 2M
channel table size: 4
timeslots when out of sync: 8
timeslots per channel: 2
sync lifetime...
When multiple J-Link devices are connected to my computer, whenever I run nrfjprog without the --snr argument, I get a prompt to select the emulator like this:
Is there...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK
I have an SPDT RF swtich is this pe42423
VDD -> VDD
LS -> P0.26
CTRL -> GND
...
Hi,
I use FDS to save my data. Below is my fds list. All RECORD already have data from factory production.
#define FILE_ID 0x1111 #define RECORD_KEY_TORQUE_0 0x0001 #define...
Hello,
I'm using nRF52833, pca10100..
My project combines the functions of scan and advertising. Each UUID is different and they pair with a different device. I initialize...
Hello, I have got the Acconeer XM122 module (v2.4) and the Acconeer XB122 module (v1.3). The XM122 is connected to the XB122 which is like a breakout board for the XM122....
We customized our own development board based on Nordic's Thingy91 development board. Now it's welded, the circuit works, and we've flash demo MQTT_simple and Asset_cracker_v2...
Hello,
Im a student trying to use the nRF52811 SoC for a project, i need to design a pcb with the chip and a few more things.
I am planning to use the available reference...
Hi,
I need to create a custom dts for a custom board where I need to define the pins used for interfacing to some external devices. The generic "gpio-leds"/"gpio-keys",...
hello Nordic
i have a project than works with nrf52840 and ncs (zephyr)
i want to have the same application running on nrf52832 as well, as part of a single code base...
Hello,
I'm trying to test example "blinky" using nRF52833 board with PCA10100. I used the pca10056 example (10100 don't exist ), and got the "Unknown function at 0x0007521E...
