Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi! I need to understand how my board is working. Right now I'm writing code on Visual Studio Code then I flash that on my board. I need to know in all of this how I'm using...
I adding an Event to Asset_Tracker_V2. I have created bms_module_evnet.h and bms_event.c files in events folder and bms_module.c. I have defined inclusion of these files in...
Hello Nordic engineer，
SDK is 15.3.0, and example is ble_app_uart
I use the "nrf_sdh_disable_request()" function to turn off Bluetooth
Then start with the function...
Hi,
Environment: nRF SDK 1.9.1, VS Code 1.66.2
Without making any changes, I can build and flash the iso_receive sample but it fails with a -5 error code (EIO) on this...
This is a cross-post from my question on StackOverflow here . This might be a more appropriate channel for this question.
I have a custom board using the u-blox BMD-350...
Dear Nordic guys,
We are going to produce large number of BLE beacon devices and would like to label the BLE address on each device. We are using the default mac address...
How Can I store information about button port ? I have two buttons P1.02 and P0.02. I have
And I have one function to init button
the most interesting is callback...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Segger Embedded Studio 4.16
I am working...
I'm trying to run LTE/BLE Gateway sample on nRF9160DK , i followed all the instruction in the sample instructions.
The Jlink RTT for nRF52840 and LTE-Link Monitor logs are...
Hi nice people, I am working on developing using visual studio and Make environment. I am trying to function UART tx/rx interrupt works but no luck. The TX and RX works perfect...
Hello,
I am currently trying to get our nRF52 development workflow working in a Docker container. I have been able to compile the firmware in the container and debug it...
Hello, I've been trying to launch zephyr SPI example, but I'm having issues with SPI sending anything. The code itself does not throw any errors, and it seems like my board...
hello sir ,
i am using thigy91 board and uploaded the asset tracker application code from ncs sample code . ii am getting humidity data on my azure cloud .but there was...
Hello everyone!
We are using nRF51822 SoC together with s130 Softdevice. nRF5 SDK v12.3.0 is used for firmware development together with the Segger Embedded Studio.
Among...
Hardware: nrf9160DK Modem FW: v1.3.1 We have been evaluating and configuring our proprietary application for NB-IoT, which is initially designed for LTE-M (CAT-M1). The Application...
