Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
I am working with SPI for the mfrc522 RFID reader. We were able to read the card previously while we used nRF connect SDK version 1.5.1 and nRF connect 3.6.1
Now I am not...
I'm using modem version mfw_nrf9160_1.3.1
It's waiting for semaphore and when CSCON notification came in between it's just resetting due to some hard fault. Can somebody...
Hi there,
I have gotten to the very last step of the following tutorial: https://www.youtube.com/watch?v=kdMJQFDRoss
The issue I am facing is that when pairing the Matter...
Hello, I tried building the app showcased in this example: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/
I have gotten everything to build fine except...
Hello,
I need some help or advice on the easiest way to perform DFU in a nRF52832 device using a nRF52820 as a central through BLE. My nRF52832 device already has the DFU...
Hello, All
I am evaluating the example, following the instruction information here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Fble_sdk_app_nus_eval...
Dear Support
Try to modify this use UART_1 for sending out data received via BLE, which is pin P0.14 on nrf52833dk_nrf52833, I modified Kconfig file under the boards folder...
Hello everyone, i am developing a board based on the nRF52832 microcontroller SDK v16.0.0 and sd132 for sending data of a sensor over BLE to a mobile APP. For this i am using...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
Hi,
I'm implementing a hard real-time system (few us jitter) on nRF52840, SDK17.1, based on FreeRTOS project.
In the project, I need to sync GPIOs toggling with ADC...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to "WRITE" a characteristic that is larger than the MTU? As an example, we are considering the following...
Dear All,
I am looking for sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board.
Your help is appreciated...
Hi,
I have a doubt regarding the possibility of removing or disabling an endpoint at runtime.
Assuming that we have a device with multiple endpoints, is there a mechanism...
Hi,
I have problem with program nrf21540 UICR mode. POUTA/B_UICR seem not set successful during measured here.
Below following which I write via SPI(Voltage is 3.5V)....
