Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I developed a custom board using nrf52810-qfaa, i edited pca10040e-s112(sdk17.1.0) and changed the advertising led to BSP_BOARD_LED_3, as i have only one led on my board at...
Hi,
I am trying to debug ESB packets with the following setup:
1. PRX (NRF52810)
2..PTX (NRF52810)
3. Sniffer (NRF52832) ( modified PRX so that it returns without...
hi ,
i am developing a zigbee network and i have used the the sample project of zigbee light bulb, switch and coordinator given in nrf5340dk. now i am facing issue with...
Hi,
I'm implementing a FOTA update procedure for the nRF9160 using the download_client from the nRF Connect SDK 1.9.1 and modem firmware 1.3.1.
In general the image update...
Hi,
I am using the nRF52840 DK to connect to an external board via the P20 shield debug out. I was wondering if any indication is given if a board is connected correctly...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
The linker script for the example code "Secure bootloader ble" for pca10040 have the FLASH section defined as:
FLASH (rx) : ORIGIN = 0x78000, LENGTH = 0x6000
According...
Hello,
I am using nRF5340 with NCS1.7.0 and nRF RPC lib for intercore communication for our product development. I followed this example ( https://github.com/nrfconnect...
Hello,
I installed NCS 2.0.0 via toolchain manager (Windows).
However, if I:
open a new cmd window
set ZEPHYR_BASE to <ZEPHYR_NCS_2_0_0_PATH>
try to build an example...
For study purpose, I try to change bootloader to move APP offset by
change APP start address to 0x20000
change start_addr in nrf_dfu_mbr_irq_forward_address_set() and...
Hi Team,
I'm using a nRF52810 board for my project but in that when I upload code using development kit, at that time my device give advertising and what I gave task.
...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Hi,
I am using the nRF9160 on a custom PCB, SDK version 1.6.1 and modem FW 1.3.1
My Application uses MQTT to send messages to a server at regular intervals. In between...
