Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
This post is just to share with all of you (who would need it) a simple application interface (attached here) that uses the nRF52840 USB since we spent some painful...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I am trying to perform the read characteristic values from the nRF52840 DK to Android studio (Java) to a TextView. I have looked at the Android Blinky example but in...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hello,
I am using an nRF52840 as a central BLE gateway with nRF connect SDK 1.8.0. I was looking for software changes to increase the scanning range. So far I've found the...
I am getting data on my Azure cloud using asset tracker code
I am enable to find tag as you can see from the Image , there was tag before sensor data , for example
before...
Hello Team,
I have a custom board based on nRF52833 platform.
I have used ble_app_uart application from S132(PCA10040) SDK
Is that okie to use S132 for nRF52833...
Hi, I'm developing an application include features
ble, 2 libuartes, pwm, timer and now I'm planning add flash to my application
1. I'm using flash_fds. I find cli.c using...
hi:
I am an new user of 52840.I want make it as an ANT+ master. Then connect some riding equipment, like cardiotachometer ,speedometer , Stepped frequency counter or other...
hello,we use nRF24l01+ for the communication of IoT,nRF24l01+ need to receive CMD from the controllors,but after a long time,nRF24l01+ cannot receive data.
we have tested...
Hi,
I want to transfer a TEXT file from my android to a NRF52 unit.
Today, In my NRF52 unit i already use NUS with NRFUART application & NRFCONNECT application to send...
Hello
We have a project working on the NRF9160 dk, however we have run into some issues with our custom board, we are using the lwm2m_client sample to prevent that firmware...
Hi All,
I am trying to drive the low freq clock necessary for the softdevice on an nrf52832 (sd s132 ver 6.1.1) with the clkout signal from an i2c real-time-clock peripheral...
Hi,
We use SDK nRF5_sdk15.2 and ARM GCC cross compiler to develop application that runs on nRF52840.
We use new lib, as it was done in examples.
I noted recently that...
When I compile ncs/nrf/applications/nrf5340_audio with the latest SDK, the code repository for LC3 is required as described in the documentation. And LC3 is not open source...
Hi All,
SDK => v17.1.0
IDE => Segger
I'm using ble_app_gls and I want to remove LESC.
According to my project =>
I have define a macro,the name is LESC, it used...
