what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
Hello nordic support:
We want to measure nRF9160's LTE RX SNR at production stage .
According to the document nwp_034--nRF9160 Hardware.pdf ==> 4.6.1. Following command...
Hi, I am working on nRF52832 as central. When I program it to form Segger Embedded Studio it's working fine but when I upload that .hex file from the nRF Connect device did...
Hi there,
We are designing a coin cell (3 V nominal) battery powered product; we'd like the ability to run it all the way down to 2.0 V for maximum lifetime. To get the...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I am trying to implement OTA buttonless DFU feature in my custom device (USB Device) which is a central device....
Hello,
I'm having some issues troubleshooting, my knowledge is limited on how to trace down where the error occurs.
Se logs below ->
Any tips on how to find...
Hi,
I start to work on the NRF52840 and I would like to read register of BMA400 in burst mode (I mean possibility to read further register in one sequence)
I am novice...
Dear Nordic,
when moveing the project to v.1.9.1 stack we've faced with a lot of
"fatal error: tinycrypt/constants.h: No such file or directory"
What is it related...
Hi folks,
SAADC peripheral gives me good results in acquiring & converting a DC signal related to current consumption.
I am using the 12-bits configuration over the internal...
I’d like to be able to read some environmental sensors and control some low power outdoor devices using the nRF52832. While I am aware that the nRF52 can operate for a long...
Hello,
NCS1.9.0 or NCS1.9.1 , Windows10 X64,VS Code,periodic_adv.default codes
with nRF52840-DK work fine.
but nRF5340-DK got error,as folow logs
"Failed to create...
Hi there,
I have just started the NCS Fundamental Course and I am stuck on Exercise 2. There are two problems that I am facing.
1) I have an nrf9160dk board. so if I compile...
Hello, I am trying to read data from the sensor using I2C, I have the nrf9160 on an Icarus board https://www.actinius.com/icarus .
I tried following this guide: https:/...
Hi Nordic Team,
I see that I am supposed to GND 2 of the SPI lines and drive the CSN high to use it in GPIO control only mode. We wanted to TP out the SPI bus for the FEM...
I am trying to send value 0x75 using I2c but when i check the value using logical analyzer i found it 0x74. and when i tried to send 0x77 i found it equal to 0x76. any help...
I am currently working on a project in which I want to transmit audio wirelessly from one nRF chip to another. Currently I am using the nRF Dongle to act as the transmitter...
