Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello devzone members,
We are producing a device based on nrf52840 that uses MBR + bootloader and an app with SDK 15.3.0.
We have set up the MBR with MBR_BOOTLOADER_ADDR...
Hi,
I'm trying to download the application by Vs Code but it was failed,the warning as below:
But when i'm trying to debug,it was worked
Have anyone can help?
...
Hello,
I am working on to program external flash (MX25R6435FZNI - Macronix) of nRF 5340 DK board using SEGGER J-Link Plus v10.1 version.
I am following Direct mode( The...
Hi,
We are currently investigating if switching to TF-M could be a good solution for us to increase our overall product security.
Our board has one nRF5340 and one nRF9160...
Hi,
I am using BL653dvk, which has nRF52833 as soc. I am working on DFU-OTA example by following this link.
https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0...
SDK : S140 17.1.0
CHIP : nRF52833
I try to write and read data by SPIM0.
Wirte works find but when read data oscilloscope like this.
But, receive buffer data...
Hi everybody,
I have some (probably) easy to solve issue with nRF52840 dongle s .
I've got from my company's collagues few dongles. With one of them I have some issues...
I try to run zephyr direction finding cnnetionless rx example, but i get some problem. every time into enable receiving of cte , i got assertion fail
this is my prj.c...
I visited the Community and wanted to up vote a post but found I had no rights to reply, post or up vote yet in the Welcome it says if I am a member of Devzone I can post...
I am trying to save data by using the setting subsystem of nrf connect sdk, and i <init> and <register> the settings, and when the setting_load function excuted, the h_set...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
I have followed the tutorials step by step on youtube( nRF Connect for VS Code, 1: Installation - YouTube ),but i still meet some errors when building the application.
The...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
I'd like to use a nRF51822-based Bluefruit LE Sniffer to read BLE advertisements (embedded with sensor data), using a python script rather than Wireshark. I've tried pyshark...
Hello,
I have recently begun to use VSCode under Linux to develop with the nRF Connect SDK and have noticed a discrepancy in the extension's functionality when using Linux...
