Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my cell phone.
The problem is that...
Hello,
I am having an issue with the nrf_libuarte_async librairie.
I am sending data via nrf_libuarte_async_tx and receiving the data properly via the IRQ handler...
Hello all, I am currently trying to get the nrf sniffer into the hardware of my nRF52840 DK board. Unfortunately when I call the programmer via the nRF Connect Desktop APP...
Hi, I am working on ble_app_uart_pca10056_s140 and after 3 minutes and I am getting the following error.
When I change APP_ADV_DURATION to 0 also get the following error...
Hi,
We have a product based on nrf52840 which is already in production for several years. It was built over SoftDevice132 and SDK 12.3.
The project has 2 components: ...
SD140
nrf52833, custom application based BLE Central Uart Project.
We would like to try the UART DMA functions available in Soft DEvice, s140_nrf52_7.2.0.
I have not...
I am trying to get I2S communication up and running but am unable to produce a signal on my SDOUT pin. MCLK, LRCLK and SCLK work as intended but trying to send any data does...
Hi! I've recently received my Thingy:91 and wanted to get it up and running. I followed your video ( https://www.youtube.com/watch?v=xQ7hDzRULJQ ), although did not see the...
Hi,
I am testing direct advertising with two nRF52-DK. One performs a direct advertising and the other scans for the directed adverts. Unfortunately, the scanning device...
The NRF52840 specifies a 20%, 10uH inductor for the integrated DCDC convertor. Why is the inductor value so large? This switcher runs at 8MHz, which usually means something...
I have been tasked to use out-of-band authentication for the nRF5340 using the NRF Connect SDK (Zephyr based). Is this feature supported within the SDK. Is there an example...
