The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi devzone, I've had UART communication problems between nRF52 and a BG96 modem for a long time.
today I added a pull down resistance on the rx of the nRF52 and it works...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
Dear All
I tried to connect to an apple device, it is successful but soon after that, it is disconnected with reason code 0x13 - terminated by remote user, I tried to change...
Good day,
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
Hi i want to make a low power delay ms (blocking) function for nrf52805 without softdevice and without NRFx, just writing to the registers.
The RTC1 events_tick never...
What is the recommended way to do DFU over Mesh in Zephyr? I saw DFU documentation in nRF5 SDK for Mesh v5.0.0 but not sure how this relates to Zephyr
Can you point me to...
Hi,
I'm running a custom nRF52811 rev1 connected to a Quectel BC660K. I'm getting this error on RTT:
Here's the initialization:
And the uart event handler:
src...
Hi Nordic Community
I have been building a thermometer device from which I would like to send temperature values via periodic advertising.
I have based the sender and...
Development setup:
2 x nRF52840 SoC
Our own PCB’s with inverted F-antenna
LE PHY 1M
nRF Connect SDK v1.8.0
Hi,
During testing we experience an issue which...
Dear Sirs.
I bought thing91 and nrf9160.
I have connected the thingy 91 with nrf9160dk with prog/debug cable but I dont able to debug the application on the thingy91....
Hello,
I am using SES Nordic Edition v5.60 and I would like to be able to include pre-processor directives in my project but I could not find the pre-processor optins. ...
Hello, im trying to send Data from one Devkit to another (nrf9160 from nrf52840) the Problem is that if i enable Bluetooth on the nRF52 i get an error when receving/transmitting...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
Hi,
I have this development board https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK . I would like to use development board as nb-IOT modem and other MCU...
