The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
i am using a custom board same as the https://devzone.nordicsemi.com/f/nordic-q-a/29195/nrf52810-custom-board
i edited pca10040e_s112.
it got stuck at sd_ble_gap_ppcp_set...
Battery free BLE solutions are exanpding (wiliot, nexite, atmosic etc). Is there a plan in Nordic to provide a low power chip that will support battery free (or at least ...
I am trying to use the MCP2515 SPI2CAN adapter with the nRF9160 DK.
I started by trying to get the Zephyr socket_can sample to work. My efforts are based on this thread...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi, I test the TCP/IP AT command in 9160DK, I download the example Serial LTE modem,
I send the command as below picture.
but it reply as below
==================...
Hello,
Is there any special area where I can save custom MAC address for each device ?
Basically I need to assign unique name and MAC address which the DFU and application...
Hey Forum,
I am using the USB Composite Keyboard example using the standard Descriptor given in the example.
I am able to get all the keys on the Host with a small caveat...
Hi,
I'm trying to use the GNSS application for the nRF9160 to compare GPS antenna performance. There is a Linux utility, GPSMON, that I'm trying to use to display side by...
I use FDS to store some application data. I performing accelerated life testing that randomly power cycles the nRF52840 (on time 4 - 10 seconds) while a central device ( Android...
Hi,
I am trying to run the fat_fs example from zephyr samples on nrf52 development kit (nrf52832) but during building I've got following error :
That's my development...
I am working on UART example and serial port.
I got compile error and modified retarget.c line 99 with
#if defined(__SES_VERSION) && (__SES_VERSION >= 34000) && !defined...
Hi，
I have a circuit board, which is powered by the battery and runs the Bluetooth program. When the power is normally supplied, it runs well. Once the USB charges the battery...
Regarding the capacitive sensor driver with adc for nrf51 series, how am I supposed to wire my board for this to work?
https://infocenter.nordicsemi.com/index.jsp?topic...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
