I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi everyone. I am writing to have an important info, that is, is it possible to load a .hex file, preloaded in an external flash, to program from my application in the nRF52840...
Hi,
As shown in the subject, I am developing a product which needs to support extern Flash-based BT OTA-upgrade. So w here can I find examples of OTA-upgrade using external...
Hi Nordic
In our product, nRF52832 is connected with another MCU through UART. We find that the overshoot in UART signal is very high.
The yellow one is the TX signal...
Dear All
I am trying connect/disconnect function with the DK, it gives me some reason codes, my app is based on central_multilink, which I cannot find their meanings, could...
Hi nordic in our product nrf52832,guided by the tutorial developer.nordicsemi.com/.../README.html,we find something strange. as we have 3 nrf52832 chips in our product,two...
Greetings,
One query on the very useful eDRx notifications in NB-IoT mode (nRF9160 SDK running 1.3.1 FW, used with MoSh app) :
I have just noticed that sometimes when...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
The datasheet of nRF52810 says that, if the voltage drops below the operating voltage, the device shall undergo a brownout reset itself and it is supposed to work normally...
Hello nordic, I'm developing a sensor that will be used sometimes in environments without LTE signal. When the sensor starts up, I'd like to check connectivity, and if there...
Hello I'm using segger,i had my own project which its name is example_detector distance , i m trying to build this project by using make -j10 . all the files were compiled...
Hello !
I was trying to communicate with my Acsip chip, when I saw that the problem was coming from the nrf_serial_read() function. And here is my setup :
- I use the...
Hello, I want to understand why some example with the "nrf52832" crash. My project is about to scan BLE device to found tags.
To start, I have tried multiples examples from...
Hi,
As far as I understand it, TF-M stores symmetric keys unencrypted on flash in the nrf91, and then uses other means (like flash read protection and trustzone) to keep...
