NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I am new to developing hardware and software with BLE, and so far have had great success with using nrf52 modules. However, I would like to get a better understanding of it...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
HI
I use SDK 17.0.0 in NRF52833.I test uart by example project ,the dir is \examples\peripheral\uart\pca10100\blank\arm5_no_packs .
Modify the baud to 921600 ,and send...
Hello,
I am attempting to update a custom C# application that is utilizing the NRFJPROG dll. We are hoping to add compatibility for multiple programmers connected to the...
We have developed a system using nRF52833 that is connected via WiFi to the cloud. We would like to do firmware update Over The Air from the Cloud using WiFi.
The first...
I used ble_app_hrs Demo to test bonding. However, I have been unable to bpnd successfully. I'll give you my bonding parameters.
#define SEC_PARAM_BOND 1
#define SEC_PARAM_MITM...
Hi,
When I increased FDS virtual pages to 50 pages and after download to device, and then used Programmer to read flash to get the images shows more longer than before,...
Hello,
I am a beginner in Zephyr, I am using the nRF 52840 DK board and I want to connect the HX711 module I have implemented nrfx_timer to make it possible to give pulse...
Hi,
I working on nrf52840 DK with nrf5 SDK17.
I tried to find out the power consumption of the peripheral(TWI/SPI) from the nrf52840 PS v1.7 document but it is not mentioned...
Hi,
I have combined a couple of examples in order to achieve the following on a custom nRF52810 board:
Count the number of pulses on a pin (using TIMER1)
Read the...
Hi, I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). Faced a problem related to the inability to connect to the MQTT broker when...
Hi
We want to run the AT command as the following, the response is always ERROR.
signal generator: CW, freq=param1-120KHz=1804.88MHz, power: -100dbm
AT%XRFTEST=4,1,3...
Hello
I need more flash and ram so I change the sdk to 13.1, but when I enabled the softdevice the log advice me use more ram.
How can I use little ram as s132_nrf52_4...
Hi,
Using the "mqtt_simple" example I found that the data_publish () function does not work for a timer handler.
In the case of the example below, when the data_publish...
Is there a way to lock NR9160 to a certain cell_id/eNB_id? I could not find any AT command for the job, but I assume that there must be a way to do it for testing purpose...
