In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I am new to developing hardware and software with BLE, and so far have had great success with using nrf52 modules. However, I would like to get a better understanding of it...
Morning Everyone,
We use raspberry pis as part of our test equipment. The final stage of our CI/CD pipeline downloads the build dfu packages to a Pi and then does an OTA...
Hi,
I try to run SDK17.1 examples/dfu/secure_bootloader/pca10040_uart_debug.
Only UART example does not have softdevice.
I build and run that example on SES on M1...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Hi Sir/Miss,
I encounter a problem which is in programmer software.
When I open software and connect to nRF52840 DK. Right flash size window will display some animation...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Hi there,
I'm currently using SDK 17.1.0 with the NRF52832 Development Board. This is pretty new to me, but the examples helped me get an application going pretty quickly...
I'm using a nrf52840dongle board with the prj_no_dfu.conf configuration with the following additions:
CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n CONFIG_CHIP_LIB_SHELL=y CONFIG_LOG...
Dear Nordic Engineers
I install nrf command line 10.1.6.0 in my office PC.There was a problem after the installation complate.
I input "nrfjprog" in powerShell ,it's normal...
Hello,
we have a remote control with 7 buttons.
Every button shall wakeup the device from deep sleep.
Beside i will have an interrupt on Button 6 and 7.
So the problem...
I am using nrfconnect 1.5.1 (zephyr/command line) with modem firmware 1.2.3 and believe I have found a fairly serious bug/behavior in the UDP API. It is pretty easy "crash...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
In the nRF5340 product specification version 1.2, I see an internal bandgap reference error range of -1.8/+0.5%.
In the nRF5340 product specification version 1.2, I see...
