hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
Hello,
On a BLE Central, how can I enable connect with auto connect to a peripheral with previously saved bonding information.
Once paired and bonded, I can recall bonding...
Hi everyone,
I am updating firmware for mesh using following this commands:
PS D:\nrf5_SDK_for_Mesh_v5.0.0_src> nrfjprog --program .\bin\softdevice\s140_nrf52_7.2.0_softdevice...
Hi everyone. I am writing to have an important info, that is, is it possible to load a .hex file, preloaded in an external flash, to program from my application in the nRF52840...
Hi,
As shown in the subject, I am developing a product which needs to support extern Flash-based BT OTA-upgrade. So w here can I find examples of OTA-upgrade using external...
Hi Nordic
In our product, nRF52832 is connected with another MCU through UART. We find that the overshoot in UART signal is very high.
The yellow one is the TX signal...
Dear All
I am trying connect/disconnect function with the DK, it gives me some reason codes, my app is based on central_multilink, which I cannot find their meanings, could...
Hi nordic in our product nrf52832,guided by the tutorial developer.nordicsemi.com/.../README.html,we find something strange. as we have 3 nrf52832 chips in our product,two...
Greetings,
One query on the very useful eDRx notifications in NB-IoT mode (nRF9160 SDK running 1.3.1 FW, used with MoSh app) :
I have just noticed that sometimes when...
With reference to the following known issue: NCSIDB-114: Default logging causes for nrf connect sdk 1.3.2. Is there any further documentation regarding the workaround mentioned...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
The datasheet of nRF52810 says that, if the voltage drops below the operating voltage, the device shall undergo a brownout reset itself and it is supposed to work normally...
Hello nordic, I'm developing a sensor that will be used sometimes in environments without LTE signal. When the sensor starts up, I'd like to check connectivity, and if there...
