I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
There have been several releases to both the Command Line Tools and Segger's JLink Software however the full Nordic toolchain still does not properly support the M1.
In...
Hi Nordic! I'm using the nrf ftp client library found here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/ftp_client.html I'm having...
Hi,
I have a nRF52833 DK which I'm evaluating for a new product which uses a UART connected GPS receiver.
I found some simple UART code which compiles OK, but crashes...
Hello, guys.
We are using nRF51822 SoC and Zephyr OS to develop our application.
I wonder if it will be possible to use Nordic's Button Handler module in the Zephyr environment...
Good afternoon,
I am working with the Thingy:91 platform and I would like to know if it is possible to get the GPS position without internet connection and if there is any...
Hi Team
1. are the following phy layer parameter like SNR,RSSI available for both WIFI and BLE?
2. if so, which register to look for such information
3. Also how about...
Hello
I am getting started on nRF SDK and I went through all the examples (at least those I'm interested about) successfully.
Now, I need to merge couple of examples together...
Hey
When i disconnect my nRF5340-DK devkit to my Lenovo T14s Gen 2 running Ubuntu 20.04.3 LTS the usb driver in the linux kernel crashes.
I think it's a problem that...
Hello there,
I've set up a Thread network with a few devices, and now I would like to connect to a ipv4 server.
At home or at the office we do not have a ipv6 public address...
Hi,
We are Migrating from nRF52832 to nRF5340 dual-core soc. In nRF52832 9 off available GPIOs were only to use with a low drive, low-frequency application since they may...
Hello,
Every time I try to run the sample gnss in SDK 1.8, I got this error gnss_sample: Failed to generate JWT, error: -8
Please can you let me what this error means...
I have starting working with UART. I see that there are two options for configuring it: UART_0_ASYNC and UART_0_INTERRUPT_DRIVEN. I want to use ASYNC option for my UART, but...
Hello
NCS1.8.0 Windows10 X64;
Can [v1.8.0\zephyr\tests\drivers\adc] convert microphone analog signal into digital signal? for I2S 8bit 8kHz
thanks
Best Regard...
I am tying to match the nRF52840 rf output to my 50 ohm 2.45GHz pcb antenna. What is the optimum rf impedance for best transmitter/receiver performance? The markings on the...
Hi, I need to fetch the Device ID of nRF5340 Chip. In datasheet Info.DeviceID[n], n = 0...1 , is mentioned. How to access this information ? Also, I am using nTF5340-DK kit...
