I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hi,
I have two 52840DK,
OS : Windows10 X64
example: \ncs1.7.1\zephyr\samples\bluetooth\periodic_sync\
I didn't change the code, Whether I set [CONFIG_BT_LL_SW_SPLIT...
Hi,
nRF Conncet SDK1.7.1, Windows10 X64.
\ncs1.7.1\zephyr\samples\bluetooth\periodic_adv\,
building and debug work well,and i set the device name "PerAdv", then reload...
Hello
I'm trying to use the example code for ble_app_uart and it doesn't seem to work. I copied the folder for pca10028 and changed processor from nrf51422 to nrf51802 everywhere...
Hello,
I'm using a combination of B0 and MCU Boot.
I want to build MCU Boot for secondary slot to try upgrading it.
I pass CONFIG_BUILD_S1_VARIANT=y to the build system...
I am using four ADC inputs to the 9160.
I am driving each input from an op amp buffer as in the attached schematic.
ADC channels 0, 2, and 3 work as expected. As for channel...
I am trying to move our existing code based on the recommended NCS SDK. I was able to get MCU boot and SMP working, however, the update is extremely slow. I now seem to be...
I have developed a project using 9160. When I start up with the client board, the log will show that at command execution error occurs when I start up. Why is this? I admit...
Hello nRF community,
I am currently testing some Memfault application that comes with the nRF SDK v1.7.0. I have a custom board designed around the nRF9160 and have been...
Hey,
I'm developing and upgrading a BT mesh to Zephyr 2.7.99 and the base functions work, but my Node keep crashing and I don't know from where. It gives the following...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
Hi!
I want to use the function strptime from time.h to convert a timestamp to unix time but get the error "implicit declaration of function 'strptime'; did you mean 'strftime...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
Hi,
I am new to microwave board design, so I'd like a little advice please. I have attached photos of the 2.4ghz section of my board and would like to know if the component...
Hi,
I'm trying to integrate the secure_bootloader DFU code into the ble_app_uart_c example but am stuck on an error regarding not fitting in an 'UNPLACED_SECTIONS' region...
