It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
I have a VS Code project that is a Workspace Application where I've had to make some modifications to code in both zephyr and mcuboot directly. My codebase is in a git repository...
Hello!
Do you have any information on the antenna itself? Radiation pattern-diagram?
Edit: I would also like to have the specs of the antenna, eg: m ismatch loss, insertion...
I am having trouble to add the toolchain folder to the VS code setup.
The nrf connect for VS code does not pop up on the side at all to add application folder.
Tried to...
Hi guys,
I try to integrate the flash logger backend .
When I run the code I get the following error:
<error> nrf_fstorage: addr_is_within_bounds(p_fs, dest, len) check...
Greetings. I am developing a application that will run on a custom board based on the nrf52833 MCU. During development we have been using a nrf52833 development kit for testing...
Mr. Jared i do apologize for having accidentally verified&closed the issue but to answer your question we've found that the module we were using did not possess a 32khz crystal...
Hi,
I am using the code provided at https://devzone.nordicsemi.com/f/nordic-q-a/85850/example-for-extended-advertisement-receive-node
to send more than 60 bytes, but unable...
hi,
I have a problem about NCS1.9.1 NVS.
I performed `nvs_write` when ble is connected and then a reset occurs:
Whether NVS write can be performed when bluetooth is...
Hello All,
I'm new to using Nordic development kit and VSCode but I am running into an issue when I am trying to build a sample application. When I use the template to create...
I am using bt_nus_send to send data via BLE every 1ms. I've noticed that when connection is bad, this function takes a couple of milliseconds to execute, while when connection...
Hi,
When sending a command using Zigbee, I understand the best method to use is by using:
So when calling light_switch_send_step, I use:
Which in turn calls below...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
Hi,
I am working NRF DK (NRF52840), when I am trying to flash the program in NRFGOSTUDIO from that it was showing some error that is " No device detected, or readback protection...
Hi, All
I am using VS Code and nRF connect v1.9.1, I try to set some parameters for scan etc. during running. It would be ideal if they can be saved into NVM and loaded...
