Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hello I'm using segger,i had my own project which its name is example_detector distance , i m trying to build this project by using make -j10 . all the files were compiled...
Hello !
I was trying to communicate with my Acsip chip, when I saw that the problem was coming from the nrf_serial_read() function. And here is my setup :
- I use the...
Hello, I want to understand why some example with the "nrf52832" crash. My project is about to scan BLE device to found tags.
To start, I have tried multiples examples from...
Hi,
As far as I understand it, TF-M stores symmetric keys unencrypted on flash in the nrf91, and then uses other means (like flash read protection and trustzone) to keep...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising, that's why I use the periodic_adv example coming with...
Hello,
I am using the vl53l5cx TOF sensor and implementing the ULD using zephyr. My setup is a bl654 board using zephyr on sdk 1.9.1. However I am running into an issue...
(replica as the previous post was archived by accident...)
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M....
Hello,
first of all i am a new user of NRF microcontrolers and embedded systems. I ve been searching on this forum for a simple PDM microphone example and although there...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
