I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello, All;
Using your nRF9160 chip to develop, there are some questions when using the network and positioning, Hope to get your answer:
1. Can LTE work at the same time...
Hello,
I have two projects, one for the application core (modified BLE Peripheral sample) and the second is for the network core (modified HCI_RPMsg sample). I am currently...
Hi all:
condition:
SDK14.2
PCA10040
example: ble_app_uart_c
I have a central device ,it need to scan RSSI value of peripheral.
If the RSSI is more than threshold...
Hello,
we were using the HRS example as a starting point and modified it for our application. Everything works fine, we can see our custom characteristics, control our device...
Is it possible, without having to join ZOI, to recompile the Zigbee ZBOSS NCP Host for the Raspberry Pi?
The NRF Connect SDK documentation under ZBOSS NCP Host states :...
Hello,
we have an custom made board with a module from raytec MDBT42q.
Our application based on the nus example.
On port 0.7 we have a led.
It seems, that there is...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
I want to add a simple GPIO pin that act as output pin, in the peripheral_uart example .
in main.c
#include <drivers/gpio.h>
//#define GPIO0_LABEL DT_PROP...
I'm using ble_app_uart_c project in nRF5 SDK 17.1 with SES.
I got 2 different devices, one is ARC EM9D AIoT DK (as Peripheral) and another is nRF52840(as Central).
I was...
Hi,
nRF9160 with SLM NCS v1.9.1 fails to attach after 7th RESET (by RESET pin) & attach without power cycle.
There is not any ERROR state reported by modem, modem fails...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code is successfully patched for nRF52805...
Hi,
I'm using the default software to check the acceleration values when there is a movement in the Thingy:91 on the LTE Monitor terminal.
The document says that this...
Hi,
I want to test of MQTT communication with nb-IOT network before going for development.
For that I have updated pre-built firmware on development board using nRF...
