Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
I have an OpenThread application that worked on NCS v1.9.1 and after updating to NCS v2.0.0 (nothing in the source code or kconfig was changed), the application fails to build...
Hello,
i found a few articels about it but none of them where helpfull for me.
I just want to use my nRF51822 Module from Raytac without an external 32khz oszillator....
I was having an issue where reading from SPI inside a timer handler always yielded 0xFF instead of the actual values. I tried to reproduce the issue with a simple test program...
I'm trying to do a firmware update over BLE.
Here's what I did: - I created a new application from sample "smp_svr" because I think that is where I can see how to do firmware...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
Hi everyone,
I'm wondering on which plateform / app and how is it possible to read and retrieve the data sent from a nRF52833 Slave to a Mobile Phone (Master) ?
We have...
I'm running on Windows 10 and am trying to connect to my BMD-350 development board with an NRF52832.
I've also attempted to execute this with Python 3.9 and 3.8 (both installed...
I'm using SDK17.1 and pca10056 DK board. I want to use app_sched_event_put for a very simple purpose. I start a one second clock whose timeout handler increments a static...
Hi
I have configured my project to have a Modbus RTU slave on UART1. When I poll the dev kit, using Modscan, I get frame length errors. I have checked baud rate and parity...
I am trying to figure out why my application is generating a hard fault. The hardware platform is nRF52832 and SDK is 17.1.0
In my experience, the generic Cortex M3 processor...
Hi,
My customer use nRF52840 with nRF5 SDK 15.0.0.
They have come up against the difficulty that uart RX pin instability.
I have searched the DevZone and it's advised...
