hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I am trying to enable UARTE0 on BMD-330 module. The serial config looks like this
# # Capabilities # CONFIG_SERIAL_HAS_DRIVER=y CONFIG_SERIAL_SUPPORT_ASYNC=y CONFIG_SERIAL_SUPPORT_INTERRUPT...
Hi,
I tried porting LC3 to my own 5340 project with reference to the SDK(nrf5340_audio_nrf5340_audio_dk_0.4.0), but I had a restart problem when initializing LC3
sw_codec_lc3_init...
Hi, I have a mature product that is programmed with a J-Link compact, I have 4 different PCs to program and a custom UI that uses command line instructions to flash PCBs....
Hello,
I'm currently developing on an NRF82832, I'm using a Black Magic Debug Probe to flash the firmware and the bootloader. I use Linux.
I have a working firmware...
Hi,
I started using nRF Connect SDK in VS Code recently. Everything works well, start a new Application, configure a new board, build, and flash.
While I found "Go to...
Hi,
I'm working on modifying the secure bootloader (SDK 17, nRF52840, s140) to store the old app before the new app is programmed into Bank 0 (see this other thread )...
Hi,
We have a design for a battery powered tag using a nrf52833-QIAA. I saw in a post from a couple years ago that you widened the DCCH inductor tolerance to +-20%. I...
Hello ,
I am trying to use NFC pin p0.10 as WAKE up pin , using nrf_gpio_cfg_sense_input(Btn, NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW); this code. I have defined CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I double-checked that when NordicUpdate_is_update_mode() returned false, I can still use the iOS Device Manager App to perform DFU.
I thought users needed to press...
Dear Nordic support Team
I have a question regarding the performance/specification of the RF front end of the NRF52 series chips. I noticed that the question "Is there an...
Hi, I'm testing the current consumption on a nRF52810.
I use PPKII to measure the current that the chip draws.
The software does the following.
Wakes up every 1 second...
Hello,
I am developing nRF52832 with SDK 16.0.0, ESB prx example.
ESB prx receive BLE and send it to UART.
UART is configured to 1000000 baud, which is maximum rate...
Hey,
I am trying to set up an application that generates interrupts on a total of 11 buttons. Setup is pretty straigt forward, for which I use the following functions for...
Hi all,
I'm using the PPK2 to measure the current of our IoT device. To get the data from my PPK2, I wrote my own software in order to integrate it into our test setup....
