I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hello,
how to activate the Early Release Assistance Indication, to bypass the RRC_CONNECTED state.
This page from Telekom suggests that the user can do that to save much...
I saw in some post smart Bluetooth can have 7 active device. I would like to know what is the maximum number of Bluetooth devices i can pair up in sleep mode? i am doing a...
Hi,
I'm using SDK v17.0.2 on my nRF52840-based board. I have implemented buttonless secure OTA reflash and it generally works. When I get the NRF_PWR_MGMT_EVT_PREPARE_DFU...
We have some dev code where the workflow is as follows:
1. an engineering version of firmware is loadded to target. The target is erased then programmed in the normal way...
Hello,
I am using nRF9160 dk for prepare a program to I2C scanning for address. Can any one give a guide for start this task. Moreover, I am using Zephyr kernel on nRF9160dk...
Hello,
I want to read external accelerometer on nrf9160dk using I2C. But when I connect SDA and SCL pins of sensor to nrf91, there is no output.
The Code is:
When...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
I'm using nrf52833 on custom board.
And I need to using RESET pin to GPIO for battery charging detection.
I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin...
Hi,
This may be a basic question. I'm using NRF52840 DK and I'm trying to print some logs from timer callback function, however I havent been successful so far. Here is...
Hi all,
I am using nrf52840 with zephyr
The below link puts device in bootloader mode but with pressing button
I want to do it without pressing button
https://devzone...
