I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
Hi, i am developing Zigbee window covering device on nrf connect sdk 1.9.1v which has 2 endpoints, but i am face issue when zigbee command is received and
device_interface_cb...
I have Ebyte’s E73-2G4M08S1C (nrf52840-QIAAC0/ aQFN73 module) where P0.19, P0.21 and P0.23 are not wired out :(
So, my question is which other pins could use / not use instead...
Dear Nordic Community,
I am trying to implement a porting of micro-ROS framework on the nRF52840 chip. As stated in their tutorial , the framework is compatible with the...
Hi,
I have started learning nRF5340 recently and have got the development kit as well.
I compiled first example of "peripheral_uart" but I am not able to program the board...
I have the ble_peripheral blinky example running, and I have a separate project with the USBD working fine (based on the usbd_cdc_acm example), but when I try to merge the...
The advtising data is 050501020304.That mean
advlen=0x05,
advtype=0x05,//BLE_GAP_AD_TYPE_32BIT_SERVICE_UUID_COMPLETE
advdata=01020304.
we want to set the 32-bit...
Dear Nordic Engineers
I use the NCS V1.9.1.I would like to building the openthread\coprocessor project on the nrf52840_dongle.I read this page: https://developer.nordicsemi...
Hi,
I found that runing a piece of code costs 490.21 us when OpenThread is disabled.
However, after OpenThread is enabled, the time changed to 746.3 us as shown in the...
In SDK17.1.0, there is an example called libuarte. Here the example uses UARTE0 to send and receive serial port data, and he is defined as follows.
NRF_LIBUARTE_ASYNC_DEFINE...
